How To Repair Concrete Holes

Big Concrete Hole Repair and Thick Physical Patch Product - Deep Patch™ past SureCrete

Large Physical Hole Patching and Thick Cement Repair Product - Deep Patch™ by SureCrete

Deep Patch™ is a only add waterconcrete patch for largephysical voids or holes. Performing well in filling low spots on horizontal surfaces and filling open areas (e.g. planters). The silicate aggregate size will cut the usual shrink cracks associated with topping mixes used for concrete repairs. Contractors and DIY homeowners akin will want to accept advantage of the benefits of Deep Patch™ for their many concrete patching projects . It tin give a suitable alternative to destroying old, damaged concrete and having to repair a new slab entirely. This product will allow the applicator just to remove the concrete areas that are too damaged to repair and make full in those voids instead of replacing the entire substrate.

Contractors will speed up a restoration process, as instead of having to wait 28 days for a freshly poured concrete to cure, most of all, customers tin can start applying a finished flooring product on top of Deep Patch™ the very next day.

Deep Patch™ a Thick Concrete Repair Product - Typical applications:

Kitchen Floors
Bath Floors
Shower Floors
Residential Living Surface area Floors
Walkways
Parking Garages
Thick Physical Repair
Patio Floors
Pool Decks
Driveways
Sidewalks
Commercial Floors
Large Concrete Hole Repair
Dwelling Concrete Cracks

How to Utilise SureCrete Deep Patch™ Concrete Hole Patching Leveling Fabric?

1. Clean the surface – Concrete substrate should be completely clear of any grease, oil, sometime pigment, etc.. Otherwise it volition not form a good bail.
2. While not always necessary, some areas may demand profiling if they are infrequent "tightly trowelled." Easily be done with another of our Surface Preparation products - SCR.
3. Dampen the surface of the concrete (no puddles, though!). So apply a thin coating of SureBond (associated product used as a bonding amanuensis, mixed with water, sold separately) to a modest work area so as not to permit it dry.

Mix Deep Patch™ with h2o thoroughly in a large bucket. While working to ensure it does not gear up before it can be practical.

Apply Deep Level to ONLY the work area where SureBond is nowadays, not dry. Continue post-obit these steps until all sectors accept been patched/covered to your satisfaction! Deep Level is typically trowelled into identify; nonetheless, application methods will vary depending on the projection needs.
Patches in excess of ii" (5 cm) upwards to iv" (10cm) require the introduction of # 8 pea gravel (3/eight - ½" [9.v – 12.7 mm]) at the rate of 10 pounds (4.5 kg) pea gravel to 1 – 50 pound (22.7 kg) bag of Deep Patch™.

Base Coat
1. Earlier applying Deep Patch™, the surface should be saturated surface dry with make clean water (SSD or damp, no puddles).
2. Apply SureBond™ according to the TDS Deep Level

Patching Coat
1. While SureBond™ is still wet, utilize Deep Level™.
two. Apply Deep Patch™ by trowel or duster, ensure the product is tightly placed into patched area.

Oftentimes Asked Questions About Deep Patch™ Large Concrete Pigsty Repair

Question: How thick tin can I go with Deep Level Big Physical Pigsty Repair?

By itself, we practise not propose going whatever thicker than 2" to repair holes. All the same, with small pea gravel aggregate into the mix, that may exist stretched and to as much as four". Come across the TDS for specific instructions on this awarding method

Question: What's the thinnest I can become with Deep Level Concrete Hole Repair? Can I give it a feather edge?

This product was not designed to be able to give a tight, feathered edge, or a finished surface. The amass size is quite large; the thinnest is can be practical 1/8". If a smoothing feathered repair concrete finished border is desired, try using i of our other products such as FlashPatch™ or SureTex™ with Deep Level.

Question: How long do I take to wait before applying an overlay on top of Deep Level Concrete Thick Repair?

While an overnight cure of 12 hours, enough for nigh coatings systems, depending on the thickness that Deep Level was applied, we suggest waiting a physical setting total 24 hours before putting any overlay or surface on top of a new Deep Level application.

Question: Can Concrete Deep Pigsty Filler and Repair Croaky be Colored?

Yes. However our coloring systems matching color charts have formulated based on white-cement-based products, then we cannot offer a typical colour chart picking and choose the finished color from, they will almost seem unlike in Deep Patch™ since it is a grey-cement-based mix.

Specifications - Properties of Deep Level Physical Deep Pigsty Filler

Coverage	0.46 cubic feet per l lb handbag
Shelf Life	12 months in unopened package
VOC Rating	0 g/L
Compressive Strength	ASTM C 109: 24 hours = 3,130 PSI (21,581 kPa); 28 days = 5,000 PSI (34,474 kPa)
Tensile Forcefulness	ASTM C 109: 1 day = 280 PSI (1,931 kPa); 28 days = 890 PSI (half-dozen,136 kPa)
Flexural Force	ASTM C 348: 1 day = 210 PSI (i,448 kPa); 28 days = 550 PSI (3,792 kPa)
Abrasion Resistance	grams lost @ one/iv" (0.635 cm) thickness: 24 hours = 1 gram; seven days = 1 gram

Deep Patch™ is thick concrete repair product Deep Concrete Patch Repair SKU: 15101001 UPC: 842467102206